outdoor fireplace feu ardent logo
Welcome to Feu Ardent's outdoor fireplaces Models of outdoor fireplaces Accessories for outdoor fireplace Assemble an outdoor fireplace Where to buy an outdoor fireplace Contact Les Foyers Feu Ardent inc. Installation du foyer extérieur #120

Assembly advises for outdoor fireplace
Picnic fireplace assembly pictures
Picnic fireplace-plus assembly pictures
Picnic with back fireplace assembly pictures
Picnic with back plus fireplace assembly pictures
Outdoor fireplace #100 assembly pictures
Outdoor fireplace #115 assembly pictures
Outdoor fireplace #120 assembly pictures
Outdoor fireplace #125 assembly pictures
Outdoor fireplace #130-3 assembly pictures
Outdoor fireplace #200-1D assembly pictures
Outdoor fireplace #200-1G assembly pictures
Outdoor fireplace #200-2 assembly pictures
Outdoor fireplace #300-2D assembly pictures

Outdoor fireplace #120

Fireplace #120's assembly

To facilitate the assembly of your outdoor fireplace, refer to the plan received at the
purchase of your fireplace and to the assembly's general section for more advices.


Put the tiles at the level.


Put the 2 blocks Start 34” and the Half-Block 26” between the rear mortises.
Reminder : The flat side of each block goes inside the fireplace.


Put the 2 blocks Start 34” so that their back are in line with the base. This way, they will
exceed by the front; it is prettier when installed this way


Place the 2 little blocks of 12” at the front.


Place the 42” (4 notches) at the back and 2 blocks of 34” (4 notches) on each side.  In putting them down,
gently tap the blocks. If there were small stones, that would crush them. Make sure that your blocks
are well placed flat over each other.


Place at the back a 42” (4 notches) and the 2 little blocks of 12”.


Place the 2 blocks of 34” (4 notches) on each side, then a 42” (4 notches) at the back
and 2 little blocks of 12” in front.


Place the 2 blocks 5 Notches 34” so that their central mortises are off-center toward the front.


Place at the front and at the back a block 42” (4 notches) and 2 little blocks of 12” in the middle.
They will support the plate.
Tip : Put some silicone under and on these 2 small blocks to prevent the smoke comes out from there.


Place the 2 blocks Arm 5 Notches 34”. From here you can start putting a thin
fillet of silicone (1/4 inch) in the chimney section.


Place the 2 blocks 42” (4 in line notches). As the chimney will decrease, put the silicone closer to the inside.
This way it will not be visible from the outside when you will put the next stone. At this stage, you can try
your plate. You will find out if your new outdoor fireplace is square. It is still time to move it a little.


Put in place your slides so that you can remove them at any time.


Place 2 blocks of 21 3/4” on each side of the chimney and 2 blocks Chimney 42” (4 off-center notches).


Place 2 blocks of 21 3/4”.


Place 2 blocks Chimney 38 5/8”.


Place 2 blocks of 21 3/4”.


Place 2 blocks Chimney 35 1/16”.


Place 2 blocks of 21 3/4”.


Place 2 blocks Chimney 31 7/16”.


Place 2 blocks of 21 3/4”.


Place 2 blocks Chimney 27 7/8”.
Tip : Do not apply silicone in your last row as it is where you will put the spark catcher.
Over time it will burn and it will easier to replace.


Place 2 blocks of 21 3/4”.


Put the little spark catcher and the 2 blocks Top 24”.


This is the end of your outdoor fireplace's assembly.

 

 


Home page  |  Fireplaces  |  Accessories  |  Assembly  |  Retailers  |  Contact us  | Franšais
Site Map
 
copyright outdoor fireplace